1 files changed, 39 insertions, 37 deletions
diff --git a/gschem/crossover.sch b/gschem/crossover.sch
index bd575a0..1bac8f1 100644
--- a/gschem/crossover.sch
+++ b/gschem/crossover.sch
@@ -1,4 +1,4 @@
-v 20110115 2
+v 20121123 2
 C 39500 37000 1 0 0 input-2.sym
 {
 T 39500 37200 5 10 1 0 0 0 1
@@ -423,34 +423,32 @@ When the cross-over is disabled, the two
 send outputs each carry the full signal.
 S401, S402, S403 are all part of the same
 triple-pole, double throw stomp switch.
-C 45400 46100 1 0 0 input-2.sym
+C 46300 45900 1 0 0 input-2.sym
 {
-T 45300 45800 5 10 1 0 0 0 1
+T 46200 45600 5 10 1 0 0 0 1
 net=PREAMP_2:1
-T 46000 46800 5 10 0 0 0 0 1
+T 46900 46600 5 10 0 0 0 0 1
 device=none
-T 45900 46200 5 10 1 1 0 7 1
+T 46800 46000 5 10 1 1 0 7 1
 value=BASS
 }
-C 49800 46100 1 180 0 input-2.sym
+C 49900 45400 1 180 0 input-2.sym
 {
-T 49800 45500 5 10 1 0 180 0 1
+T 49900 44800 5 10 1 0 180 0 1
 net=XOVER:1
-T 49200 45400 5 10 0 0 180 0 1
+T 49300 44700 5 10 0 0 180 0 1
 device=none
-T 48600 45700 5 10 1 1 180 7 1
+T 48700 45000 5 10 1 1 180 7 1
 value=XOVER
 }
-C 47200 46000 1 0 0 switch-spdt-1.sym
+C 47500 48100 1 0 0 switch-spdt-1.sym
 {
-T 47600 46800 5 10 0 0 0 0 1
+T 47900 48900 5 10 0 0 0 0 1
 device=SPDT
-T 47600 46600 5 10 1 1 0 0 1
+T 47900 48700 5 10 1 1 0 0 1
 refdes=S401
 }
-N 47200 46200 46800 46200 4
-N 48100 46400 49800 46400 4
-N 48100 46000 48400 46000 4
+N 48400 46400 49800 46400 4
 T 50000 39800 9 10 1 0 0 0 3
 This dual pot is wired to blend the two signals.
 As the resistance of one pot increases, the other
@@ -593,7 +591,7 @@ N 52500 37400 55400 37400 4
 N 54000 38300 54000 38700 4
 N 54000 38700 54200 38700 4
 N 55100 38700 55400 38700 4
-N 55700 37400 58400 37400 4
+N 56300 37400 58400 37400 4
 C 60900 36800 1 180 0 input-2.sym
 {
 T 61300 36500 5 10 1 0 180 0 1
@@ -784,7 +782,7 @@ footprint=R025
 N 54800 43100 54800 44200 4
 N 54800 44200 55200 44200 4
 N 55200 44200 55200 43500 4
-T 46100 47800 9 10 1 0 0 0 1
+T 46200 47500 9 10 1 0 0 0 1
 40{1,2,3}-2 are connected at the switch contacts, off-board.
 C 53400 47900 1 0 0 connector1-2.sym
 {
@@ -795,24 +793,6 @@ device=CONNECTOR_1
 T 53700 48950 5 10 0 0 0 0 1
 footprint=CONNECTOR 1 1
 }
-C 47000 44600 1 0 0 connector1-2.sym
-{
-T 47700 45500 5 10 1 1 0 6 1
-refdes=CONN410
-T 47300 45450 5 10 0 0 0 0 1
-device=CONNECTOR_1
-T 47300 45650 5 10 0 0 0 0 1
-footprint=CONNECTOR 1 1
-}
-C 48300 44200 1 0 0 connector1-2.sym
-{
-T 49000 45100 5 10 1 1 0 6 1
-refdes=CONN411
-T 48600 45050 5 10 0 0 0 0 1
-device=CONNECTOR_1
-T 48600 45250 5 10 0 0 0 0 1
-footprint=CONNECTOR 1 1
-}
 C 51700 47900 1 0 0 connector1-2.sym
 {
 T 52400 48800 5 10 1 1 0 6 1
@@ -843,8 +823,30 @@ footprint=CONNECTOR 1 1
 N 53400 48300 53300 48300 4
 N 53300 48300 53300 47000 4
 N 51700 48300 51700 46400 4
-N 48300 46000 48300 44600 4
-N 47000 46200 47000 45000 4
 N 53400 44800 53200 44800 4
 N 52300 43300 51800 43300 4
 N 51800 43300 51800 45300 4
+N 48500 45300 48400 45300 4
+N 48400 45300 48400 46400 4
+N 47700 46000 48400 46000 4
+T 48700 48500 9 10 1 0 0 0 1
+Switch for LED
+T 45900 46900 9 10 1 0 0 0 2
+TODO: is it a problem to always connect
+the bass preamp output to the crossover?
+C 55900 37700 1 0 0 capacitor-4.sym
+{
+T 56100 38800 5 10 0 0 0 0 1
+device=POLARIZED_CAPACITOR
+T 56100 38200 5 10 1 1 0 0 1
+refdes=C450
+T 56100 38400 5 10 0 0 0 0 1
+symversion=0.1
+T 55900 37700 5 10 1 1 0 0 1
+value=10u
+T 55900 37700 5 10 0 1 0 0 1
+footprint=RCY100P
+}
+N 55900 37900 55700 37900 4
+N 56800 37900 57100 37900 4
+N 57100 37900 57100 37400 4