diff options
| -rw-r--r-- | gschem/crossover.sch | 76 |
1 files changed, 39 insertions, 37 deletions
diff --git a/gschem/crossover.sch b/gschem/crossover.sch index bd575a0..1bac8f1 100644 --- a/gschem/crossover.sch +++ b/gschem/crossover.sch @@ -1,4 +1,4 @@ -v 20110115 2 +v 20121123 2 C 39500 37000 1 0 0 input-2.sym { T 39500 37200 5 10 1 0 0 0 1 @@ -423,34 +423,32 @@ When the cross-over is disabled, the two send outputs each carry the full signal. S401, S402, S403 are all part of the same triple-pole, double throw stomp switch. -C 45400 46100 1 0 0 input-2.sym +C 46300 45900 1 0 0 input-2.sym { -T 45300 45800 5 10 1 0 0 0 1 +T 46200 45600 5 10 1 0 0 0 1 net=PREAMP_2:1 -T 46000 46800 5 10 0 0 0 0 1 +T 46900 46600 5 10 0 0 0 0 1 device=none -T 45900 46200 5 10 1 1 0 7 1 +T 46800 46000 5 10 1 1 0 7 1 value=BASS } -C 49800 46100 1 180 0 input-2.sym +C 49900 45400 1 180 0 input-2.sym { -T 49800 45500 5 10 1 0 180 0 1 +T 49900 44800 5 10 1 0 180 0 1 net=XOVER:1 -T 49200 45400 5 10 0 0 180 0 1 +T 49300 44700 5 10 0 0 180 0 1 device=none -T 48600 45700 5 10 1 1 180 7 1 +T 48700 45000 5 10 1 1 180 7 1 value=XOVER } -C 47200 46000 1 0 0 switch-spdt-1.sym +C 47500 48100 1 0 0 switch-spdt-1.sym { -T 47600 46800 5 10 0 0 0 0 1 +T 47900 48900 5 10 0 0 0 0 1 device=SPDT -T 47600 46600 5 10 1 1 0 0 1 +T 47900 48700 5 10 1 1 0 0 1 refdes=S401 } -N 47200 46200 46800 46200 4 -N 48100 46400 49800 46400 4 -N 48100 46000 48400 46000 4 +N 48400 46400 49800 46400 4 T 50000 39800 9 10 1 0 0 0 3 This dual pot is wired to blend the two signals. As the resistance of one pot increases, the other @@ -593,7 +591,7 @@ N 52500 37400 55400 37400 4 N 54000 38300 54000 38700 4 N 54000 38700 54200 38700 4 N 55100 38700 55400 38700 4 -N 55700 37400 58400 37400 4 +N 56300 37400 58400 37400 4 C 60900 36800 1 180 0 input-2.sym { T 61300 36500 5 10 1 0 180 0 1 @@ -784,7 +782,7 @@ footprint=R025 N 54800 43100 54800 44200 4 N 54800 44200 55200 44200 4 N 55200 44200 55200 43500 4 -T 46100 47800 9 10 1 0 0 0 1 +T 46200 47500 9 10 1 0 0 0 1 40{1,2,3}-2 are connected at the switch contacts, off-board. C 53400 47900 1 0 0 connector1-2.sym { @@ -795,24 +793,6 @@ device=CONNECTOR_1 T 53700 48950 5 10 0 0 0 0 1 footprint=CONNECTOR 1 1 } -C 47000 44600 1 0 0 connector1-2.sym -{ -T 47700 45500 5 10 1 1 0 6 1 -refdes=CONN410 -T 47300 45450 5 10 0 0 0 0 1 -device=CONNECTOR_1 -T 47300 45650 5 10 0 0 0 0 1 -footprint=CONNECTOR 1 1 -} -C 48300 44200 1 0 0 connector1-2.sym -{ -T 49000 45100 5 10 1 1 0 6 1 -refdes=CONN411 -T 48600 45050 5 10 0 0 0 0 1 -device=CONNECTOR_1 -T 48600 45250 5 10 0 0 0 0 1 -footprint=CONNECTOR 1 1 -} C 51700 47900 1 0 0 connector1-2.sym { T 52400 48800 5 10 1 1 0 6 1 @@ -843,8 +823,30 @@ footprint=CONNECTOR 1 1 N 53400 48300 53300 48300 4 N 53300 48300 53300 47000 4 N 51700 48300 51700 46400 4 -N 48300 46000 48300 44600 4 -N 47000 46200 47000 45000 4 N 53400 44800 53200 44800 4 N 52300 43300 51800 43300 4 N 51800 43300 51800 45300 4 +N 48500 45300 48400 45300 4 +N 48400 45300 48400 46400 4 +N 47700 46000 48400 46000 4 +T 48700 48500 9 10 1 0 0 0 1 +Switch for LED +T 45900 46900 9 10 1 0 0 0 2 +TODO: is it a problem to always connect +the bass preamp output to the crossover? +C 55900 37700 1 0 0 capacitor-4.sym +{ +T 56100 38800 5 10 0 0 0 0 1 +device=POLARIZED_CAPACITOR +T 56100 38200 5 10 1 1 0 0 1 +refdes=C450 +T 56100 38400 5 10 0 0 0 0 1 +symversion=0.1 +T 55900 37700 5 10 1 1 0 0 1 +value=10u +T 55900 37700 5 10 0 1 0 0 1 +footprint=RCY100P +} +N 55900 37900 55700 37900 4 +N 56800 37900 57100 37900 4 +N 57100 37900 57100 37400 4 |